Device Installation Archives - Rigsters

Unboxing and Assembly – Video

admin — Tue, 05 Dec 2023 10:54:46 +0000

The post Unboxing and Assembly – Video appeared first on Rigsters.

Arago Assembly

admin — Tue, 05 Dec 2023 11:13:04 +0000

Below is a 10-step guide outlining the process of assembling Arago after removing it from the transportation box.

1. Unlock Latches

Unlock all four latches at the back of the unit to separate the individual components.

2. Release Two Knobs

Release the two knobs located in the back sides of the unit by rotating them counterclockwise.

3. Lift Arago in Upright Position

Fully elevate the vertical (Y) component by the top handle located in the back of the unit as illustrated.

4. Tighten Knobs

Fully tighten the two knobs from the previous step by rotating them clockwise. This secures the Y vertical component in place.

5. Release Four Knobs

Loosen the four knobs on the payload (T – tilt) component, with two on each side of the unit. Turn the knobs counterclockwise to release, but do not completely unscrew them from the unit.

6. Elevate Tilt

Using the designated cutouts on each side, fully lift the T component as shown. While keeping the T component elevated, gently pull it towards you and then lower it until it is secured in a horizontal position.

7. Tighten Four Knobs

Rotate the four knobs clockwise to fully tighten them, securing the T component in place.

8. Lift Turntable

Using the dedicated handles on either side, lift the turntable (Z) component from the back of the unit and position it in front. Align the two ball catchers/silver joints on the sides of the turntable (Z) and horizontal (X) components, and click them together.

9. Connect Turntable

Link the horizontal (X) and turntable (Z) components using the supplied D-sub (20cm) cable. The orientation of the cable doesn’t matter. After inserting the connector fully on both ends, press the small metal lock on the side outward to secure the connection.

10. Connect Cables

Connect the following four provided cables at the back of the unit:

LAN data cable
USB data cable
Power cable – Arago in
Power cable – Arago built-in Power Extender

Observe the indication labels on the port panel of the unit to ensure correct connections. If you’re not utilizing the mounted power outlets (x3) located on the lower part of the system, cable (4) can be skipped.

WARNING
Arago must be used only with provided original cables and have a secure grounded connection. Misuse can lead to damaging the device.

The post Arago Assembly appeared first on Rigsters.

Unboxing Arago

admin — Tue, 05 Dec 2023 11:17:26 +0000

Please follow these steps to remove Arago from the transportation case:

1. Make sure the case is placed on an even solid surface that can withstand weight.

2. Make sure that all 6 wheel brakes are locked.

3. Release the locks of all 6 latches positioned on the sides of the case.

4. Lift the top lid

of the transportation case by the handles located on the front and the back sides of the case. Do not use the handles on the long sides.

It is important that the lid is lifted straight upwards and not at an angle. Don’t use force while opening the case. Place the lid on the ground.

5. Remove Arago from the case.

Decide beforehand which side of the case the unit will be laid down after you take it out. Make sure there are no obstructions on the ground surface.

Lifting the Arago unit out of the case must be performed by two authorised persons. The unit must be lifted from the box only by the designated handles at the ends of the system as illustrated.
Due to the weight of the unit, it is necessary for operators to keep their back straight and lift simultaneously.
As soon as the unit is lifted out of the case, step to the side and place the unit on the ground next to the case.

The post Unboxing Arago appeared first on Rigsters.

Turntable Extension

admin — Tue, 05 Dec 2023 11:20:50 +0000

This section describes the necessary steps for mounting turntable extension module to elevate your subjects.

1. Screw in rods

Attach the four 30 cm extension rods to the base turntable plate by screwing them on. Avoid over-tightening the rods.

2. Mount plate

Position one of the base plates on top of the rods, aligning the plate holes with the tips of the rods. If the height is sufficient, secure the plate to the rods using the provided bolts.

3. Additional extension

If further extension is needed, secure the plate with four additional rods instead of using the bolts from the previous step. Ensure there is a plate between the two sets of rods for added stability.

4. Mount top plate

Attach the last top base plate and secure it with bolts. Ensure the overall stability of the modules and re-tighten the components if necessary.

The post Turntable Extension appeared first on Rigsters.